Wireless Water Resistant Sensors
High Water Sensor, Low Voltage Sensor, Tempsensor, Deck Pressure Sensors, Wireless Delay, Infrared Beam Sensor, Snap Canvas Snap Sensor, Door/Hatch Sensor, Standard Wide-Gap Extension Sensor, Super Heavy Duty Wide Gap Extension Sensor, Recessed Extension Sensor, Standard Wide Gap with Hidden Wire Extension Sensor
Click on Images for details and larger view
|
 |
|
|
GMM-IP67 : Pull Sensor
The GOST GMM-IP67-Pull Sensor is a great sensor with multiple uses. Notification is given if the boat is
pulled away from the dock, or the back of a yacht. It is also possible to install the sensors in several
different ways. They can be installed with the female end on the dock or the mother ship, or they
can have the male & female on the same vessel, which lends itself to more versatility. The sensor will
cause the security system to go into alarm if the sensor is either pulled out or cut without first disarming
the system. We designed this sensor to combat thieves coming up to vessels when they are tied up at night
and cutting the lines and towing the vessel away with jet skis or other small watercraft which we have seen an
increase in recent months.
|
 |
|
 |
|
GMM-IP67-HWS : High Water Sensor
|
GMM-IP67-HWS : High Water Sensor
The GMM-IP67-HWS wireless High Water Sensor is designed to stand up to the harsh marine environment and includes a mounting bracket for the float switch that should be installed in the bilge of the vessel slightly below the vessels factory installed high water sensor.
|
 |
|
|
GMM-IP67-LVS : L12/24 - Low Voltage Sensor
|
GMM-IP67-LVS : L12/24 - Low Voltage Sensor
The GMM-IP67-LVS wireless Low Voltage Sensor is designed to stand up to the harsh marine environment and is set to trigger an alarm when the voltage drops below 11.6v (on 12V Sensor) or 23.2v (on 24v sensor) for more than 2 minutes. This sensor will monitor any 12V or 24V battery bank. There is a dip switch on the circuit board that allows installers to switch the voltage monitored between 12 or 24 volts DC.
|
 |
|
|
|
GMM-IP67-TempSensor
The GMM-IP67-TempSensor wireless Temperature Sensor transmitter enclosure is designed to stand up to the harsh marine environment and is set to trigger an alarm when the temperatures exceed or drops below a preset temperatures range. The coil sensor itself can be mounted virtually anywhere in the vessel where temperature threshold alarms are needed.
|
 |
|
|
GMM-IP67-DS : Deck Pressure Sensors
|
GMM-IP67-DS : Deck Pressure Sensors
The GMM-IP67-DS wireless Deck sensor is designed to protect the exterior or interior of the vessel. The sensors are epoxied to the underside of the vessel’s deck where they cannot be seen by intruders. In addition, they will not detract from the vessels decor. These sensors are effective on almost any boat structure including wood, fiberglass and even aluminum or steel decks. Environmentally sealed and utilizing 22-gauge marine grade wire leads, these sensors are ideal for those hard to protect areas of the vessel where there is access to the underside of the deck. They will not respond to vibration, shock, or airborne items. They sense only the unique flexing of the deck caused by a person walking. Sensitivity is fully adjustable from the processor. They can even be used to protect ladders up to the fly bridge or tuna tower.
|
 |
|
|
GMM-IP67-RLY-Z1 : Water resistant wireless relay
|
GMM-IP67-RLY-Z1 : Water resistant wireless relay
The GMM-IP67-RLY-Z1 is the water resistant version of the RLY-Z1 above
and is for use on the exterior of vessels, or on vessels where everything
has the potential to get wet, like on a center console. |
|
|
|
GMM-IP67-IBS : Infrared Beam Sensor
|
GMM-IP67-IBS : Infrared Beam Sensor
The GMM-IP67-IBS wireless infrared beam sensor is designed to protect the exterior of the vessel. There is an invisible infrared beam between the emitter and the detector (photoelectric eyes). Once the infrared beam is broken the sensor is activated and causes the system to go into alarm. These sensors are commonly installed in the gunwales to protect the cockpit areas. Other uses include open fly bridges to protect the electronics or any other exposed areas where a motion detector is not practical. These sensors have a built in fail safe amplifier and are resistant to sunlight and other interference. These sensors are also available with 2 sets of photoelectric eyes. |
 |
|
|
GMM-IP67-Snap : Canvas Snap Sensor
|
GMM-IP67-Snap : Canvas Snap Sensor
The GMM-IP67-CSS wireless Canvas Snap Sensor is designed to stand up to the harsh marine environment and is set to trigger an alarm when the canvas cover is unsnapped. The canvas snap sensor is mounted in an existing snap location by drilling a 25/64” hole thru the vessel. The sensor is inserted in the drilled hole and secured with the brass nut on the underneath side. An O-ring under the snap base provides a seal to keep water from entering around the sensor head. This sensor is great for protecting vessels that are covered with a canvas cover. Because of its exceptional design, it is impossible to see, as the sensor looks like a normal snap when properly installed. |
 |
|
|
GMM-IP67-DC : Water resistant door/hatch sensor
|
GMM-IP67-DC : Water resistant door/hatch sensor
Our long range water resistant wireless door/hatch sensor works with any of our available extension sensors below. It is compatible with the GOST Marine Magellan, GOST Insight Systems & GOST NT-Evolution. This wireless design also has a built in anti-tamper switch.
Features:
• Wireless range in a typical marine
environment: 35m (115ft) with GOST
Marine Magellan or GOST Insight that
can be extended to 70m (230ft) with
the Wireless Repeater
• Low battery and signal
transmission LED
Read more...
|
|
|
|
GDC-EXT-WG : Standard Wide Gap Extension Sensor
|
GDC-EXT-WG : Standard Wide Gap Extension Sensor
Miniature Surface Mount Switch Set Wide
Gap up to 3 inch gap between sensor and
magnet (white). |
 |
|
|
